Navigation Lights: Getting Them Right for Nighttime Safety and Compliance

Being seen at night is not optional. A vessel that is invisible—or that shows the wrong lights—creates one of the highest-risk situations on the water. Navigation lights exist so other mariners can determine your presence, heading, and status (under power, under sail, at anchor) at a distance. The operator, not the builder, is ultimately responsible for ensuring those lights are the correct type, properly certified, correctly installed, unobstructed, and working.

The Regulatory Framework

Two sets of rules govern navigation lights in U.S. waters:

  • The International Regulations for Preventing Collisions at Sea (COLREGS) apply on the high seas and in waters where COLREGS are in force.

  • The U.S. Inland Navigation Rules (33 CFR) apply on inland waters.

Both are administered by the U.S. Coast Guard. In addition:

  • ABYC A-16 (Installation of Electric Navigation Lights) provides the primary guidance for installation on vessels under 20 meters (65.6 ft). Compliance is strongly recommended for all boats.

  • ABYC C-5 (Construction and Testing of Electric Navigation Lights) covers design, performance, color, intensity, service life, and electromagnetic compatibility. The Coast Guard has accepted ABYC C-5 as equivalent to the older UL 1104 standard. This is especially important for LED lights.

Lights installed on vessels built on or after November 1, 2003 must be third-party certified and permanently marked with the USCG range (e.g., “USCG 2 nm”). Temporary stickers or unmarked lights do not meet the requirement. Older vessels must still meet the performance and configuration rules even if the certification path was different.

Required Configurations

Requirements depend on length overall (LOA) and whether the vessel is under power or under sail. LOA includes the hull and permanent appendages but generally excludes items such as a bowsprit.

Power-driven vessels

  • Under 12 m (39.4 ft): Sidelights (minimum 1 nm) plus either a separate masthead light (2 nm, at least 1 m above the sidelights) and stern light (2 nm), or a single all-round white light in lieu of the masthead and stern lights.

  • 12 m to under 20 m: Sidelights (2 nm), masthead light (3 nm, at least 2.5 m above the gunwale and as far forward as practicable), and stern light (2 nm). Vertical separation rules apply; placing masthead and sidelights on the same structure often violates the height requirement.

  • 20 m and larger: Higher ranges and stricter positioning (masthead often 5 nm or more).

Sailing vessels under sail alone

  • Under 12 m: Sidelights (1 nm) and stern light (2 nm), or a combination bi-color, or a masthead tricolor.

  • 12 m to under 20 m: Sidelights (2 nm) and stern light (2 nm), or a tricolor.

  • A tricolor is permitted only when under sail alone. It must never be used when the engine is running. When under power (even with sails up), a sailboat is a power-driven vessel and must show the appropriate power configuration plus a day-shape cone when appropriate.

At anchor

  • Most vessels show a single all-round white light (2 nm minimum) where it can best be seen. Larger vessels have additional requirements. Special anchorage areas may have exemptions.

Installation Best Practices

Correct hardware is only half the job. Placement and orientation determine whether the lights actually work.

  • Mount sidelights on vertical surfaces that are parallel to the centerline and level when the boat is at rest. Use shims if the surface is not vertical so the fixture is oriented at 90 degrees.

  • Prefer sidelights above the sheerline. Mounting below the sheerline reduces visibility when the boat is heeled and is non-compliant under COLREGS.

  • Masthead and stern lights should be vertical and perpendicular to the centerline. Place the masthead light as far forward as practicable.

  • Ensure the required arcs are clear of davits, antennas, radar, flags, passengers, or other gear. All-round lights may not be obscured by more than 6 degrees by a mast or structure.

  • Install shades or baffles on masthead or all-round lights so they do not shine into the operator’s eyes or reflect off the deck or superstructure and destroy night vision.

  • On tenders, bow-mounted sidelights are usually better than rail-mounted ones; they are less likely to be blocked by people or to reflect off tubes.

  • Use a two-position switch (or equivalent interlock) so that the steaming-light configuration and the sailing configuration cannot be illuminated at the same time.

  • Brackets must be rugged. Lights should not be supported solely by the wiring.

LED Lights: Advantages and Cautions

LEDs draw far less current, last longer, and resist vibration better than incandescent bulbs. They are now the practical choice for most vessels, provided they meet ABYC C-5 (or the older accepted standard) and carry the proper permanent USCG marking.

Important caveats:

  • Do not simply drop an LED bulb into an old incandescent fixture. The combination is almost never certified and voids compliance.

  • Confirm the light is rated for your vessel’s DC voltage range (many modern units accept 10–30 V).

  • Some LED lights generate radio-frequency interference that can affect VHF, AIS, or GPS. Perform a real-world EMC check after installation—turn the lights on and listen/watch for interference.

  • Wiring must be properly supported and sealed. Heat-shrink, sealant, and proper strain relief are required; the fixture itself should not carry the weight of the cable.

Common Problems and Maintenance

Typical defects found on otherwise well-kept boats include:

  • Inoperative lights or lights with water inside the lens (corrosion follows quickly).

  • Crazed or yellowed lenses that reduce range and alter color.

  • Incorrect orientation (upside-down or tilted fixtures).

  • Overlapping red and green sectors from poorly aimed bi-color lights.

  • Obstructions from added cruising gear.

  • Use of a single all-round light where separate masthead and stern lights are required.

  • Simultaneous illumination of sailing and power configurations.

Inspect lights regularly, especially those that are difficult to reach. Check operation, look for moisture, and verify that arcs remain clear after any deck work or equipment additions. For older incandescent fixtures, use the correct wattage bulb, clean corrosion from the base, and apply dielectric grease. Prefer fixtures that can be serviced without tools when possible.

The Bottom Line

Navigation lights are a primary collision-avoidance system. Choose certified lights rated for your vessel’s length, install them according to ABYC A-16 and the Navigation Rules so the arcs are clear and the orientation is correct, and never display the wrong configuration for the way you are operating. Regular inspection and prompt repair of even minor defects keep you visible—and keep other vessels from mistaking your intentions.

Fair winds and clear horizons.

Next
Next

Smoke Detectors on Boats: The Early Warning System Every Captain Should Install